8069729 Festo

FESTO 8069729 integrated drive

Name: 8069729 FESTO
Brand: FESTO
SKU: 673597-en-gbp
Price: 1074.69 GBP
Availability: SoldOut

EMCA-EC-67-S-1TE-EC

£1,074.69

Limited stock only available on quotation

Specifications

Series (EMCA)	Motor with controller
Motor type (EC)	EC motor
Flange size, motors (67)	67
Length (S)	Short
Nominal operating voltage (1)	24 V DC

Electrical connection (T)	Terminal box
Measuring unit (E)	Encoder
Brake	None
Bus protocol/activation (EC)	EtherCAT®
Degree of protection, electrical system	Standard

Technical data

Note on materials		Contains paint-wetting impairment substances RoHS-compliant
Switching logic for outputs		PNP (positive switching)
Ethernet, supported protocols		TCP/IP
Working range of logic input		24 V
Communication profile		CiA402 FHPP
Number of digital logic outputs 24 V DC		2
Proof test interval		20 y
Permissible axial shaft load		60 N
Nominal torque		0,37 Nm
Note on ambient temperature		Power must be reduced by 1.75% per °C at ambient temperatures above 20°C.
Degree of protection		IP54
Media redundancy		Ring redundancy
Shock resistance		Shock test with severity level 2 to FN 942017-5 and EN 60068-2-27
CE mark (see declaration of conformity)		To EU EMC Directive To EC Machinery Directive
KC mark		KC-EMV
Permissible voltage fluctuations		+/- 20 %
Max. output motor		158 W
Max. number of process sets		64
SFF Safe Failure Fraction		> 90 %
Parameterisation interface		Ethernet
Nominal voltage DC		24 V
Max. negative test pulse with 1 signal		600 µs
Max. current digital logic outputs		100 mA
Features of digital logic outputs		Freely configurable in some cases Not galvanically isolated
Brake resistor, external		6 Ohm
Nominal rotary speed		3.100 rpm
Display		LED
Safety Integrity Level (SIL)		Safe torque off (STO)/SIL 2
Additional functions		CoE (CSP only) Distributed clocks Emergency message Variable PDO mapping
Protective function		I²t monitoring Temperature monitoring Current monitoring Voltage failure detection Following error monitoring Software end-position detection
Rotor position sensor		Absolute single-turn encoder
Configuration support		ESI file

Type of mounting		Screw-clamped With through-hole
Switching logic for inputs		PNP (positive switching)
Features of logic input		Galvanically connected to logic potential
Specification logic input		Based on IEC 61131-2
Number of digital logic inputs		2
Product weight		1.900 g
Permissible radial shaft load		100 N
Peak torque		0,85 Nm
Mass moment of inertia of rotor		0,175 kgcm²
Ambient temperature		0 °C ... 50 °C
Relative air humidity		0 - 95% Non-condensing
Storage temperature		-25 °C ... 70 °C
Vibration resistance		Transport application test with severity level 2 to FN 942017-4 and EN 60068-2-6
Certificate issuing authority		TÜV 01/205/5514.00/16 UL E331130
Approval		RCM trademark c UL us - Recognized (OL)
Peak current		10,2 A
Rotor position transducer resolution		12 bit
Operating time absolute encoder		With external battery: up to 6 months Note: the maximum service life of the battery depends on its charging status, the ambient temperature and ageing effects. Without external battery: 3 days (worst case) up to max. 7 days (best case) Note: The maximum storage time depends on the charge state of the internal capacitor, ambient temperature and ageing effects.
Protocol		EtherCAT
Nominal current		6,9 A
Nominal power rating of motor		120 W
Max. positive test pulse with 0 signal		10.000 µs
Hardware fault tolerance		1
Diagnostic coverage		90 %
Baud rate		10/100 Mbit/s (full/half)
Max. rotational speed		3.500 rpm
Performance Level (PL)		Safe Torque Off (STO)/category 3, performance level d
Safety function		Safe torque off (STO)
Topologies		Star Ring Line
Rotor position sensor, encoder measuring principle		Magnetic
Min. cycle time		2 ms
Controller operating mode		PWM MOSFET power output stage Cascade controller with P position controller PI speed controller PI current regulator